arch/arm/boot/dts/amlogic/meson8b_m201_1G.dtd

/dts-v1/;
/// ***************************************************************************************\n
//$$ PROJECT="meson8b"
//$$ REMOVE 1
void root_func(){
//$$ ADD /{
	amlogic-dt-id = "m8b_m201_1G";
	compatible = "AMLOGIC,8726_M8B";
	model = "AMLOGIC";
	interrupt-parent = <&gic>;
	#address-cells = <1>;
	#size-cells = <1>;
	
/// ***************************************************************************************
///	-	CPU
//$$ MODULE="CPU"
    cpus {
        #address-cells = <1>;
        #size-cells = <0>;
//$$ DEVICE="cpu0"
        cpu@0 {
        	device_type = "cpu";
        	compatible = "arm,cortex-a5";
        	reg = <0x200>;
        };
//$$ DEVICE="cpu1"
        cpu@1 {
        	device_type = "cpu";
        	compatible = "arm,cortex-a5";
        	reg = <0x1>;
        };
//$$ DEVICE="cpu2"
        cpu@2 {
        	device_type = "cpu";
        	compatible = "arm,cortex-a5";
        	reg = <0x2>;
        };
//$$ DEVICE="cpu3"
        cpu@3 {
        	device_type = "cpu";
        	compatible = "arm,cortex-a5";
        	reg = <0x3>;
        };
    };

/// ***************************************************************************************
///	-	Cache
//$$ MODULE="Cache"
//$$ DEVICE="cache"
    cache-controller {
          compatible = "arm,meson-pl310-cache";
          reg = <0xc4200000 0x1000>;
          arm,data-latency = <3 3 3>;
          arm,tag-latency = <2 2 2>;
          arm,filter-ranges = <0x100000 0xc0000000>;
          cache-unified;
          cache-level = <2>;
          aux-instruction_prefetch;
          aux-data_prefetch;
          aux-ns_lockdown;
          aux-force_no_write_alloc;
          aux-cache_replace_policy_round_robin;
          aux-early_write_response;
          aux-full_line_of_zero;
          aux-ns_int_ctrl;
          aux-share_override;
          prefetch-double_line_fill;
          prefetch-prefetch_drop;
          prefetch-prefetch_offset = <7>;
    };

/// ***************************************************************************************
///	-	Memory
//$$ MODULE="Memory"
//$$ DEVICE="memory"
//$$ L2 PROP_U32 = "aml_reserved_start"
//$$ L2 PROP_U32 = "aml_reserved_end"
//$$ L2 PROP_U32 6 = "linux,usable-memory"
	memory{
		device_type = "memory";
		aml_reserved_start = <0x06000000>; /**reserved memory start */
		aml_reserved_end = <0x05000000>;/**reserved memory end : dtb start for uboot*/
		phys_offset = <0x00200000>;
		linux,total-memory = <0x3fe00000>;
      #address-cells = <1>;
      #size-cells = <1>;

//      cma_0:region@0 {
//         region_name = "cma_0";
//         reg = <0 0x02a00000>;
//         linux,contiguous-region;
//      };
	};
/// ***************************************************************************************
///	-	GIC
//$$ MODULE="GIC"
//$$ DEVICE="gic"	
	gic:interrupt-controller{
        compatible = "arm,cortex-a9-gic";
        reg = <0xc4301000 0x1000
               0xc4300100 0x0100>;
        interrupt-controller;
        gic_fiq_enable;
        #interrupt-cells = <3>;
        #address-cells = <0>;
    };
    
/// ***************************************************************************************
///	-	VPU
//$$ MODULE="VPU"
//$$ DEVICE="vpu"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 = "clk_level"
    vpu{
		compatible = "amlogic,vpu";
		dev_name = "vpu";	
		status = "ok";
		clk_level = <3>;
		/**    	0: 106.25M		1: 127.5M		2: 159.375M
				3: 182.15M		4: 212.5M	 */
	};
	
/// **************************************************************************************	
/// -   DISP&MM-FB
//$$ MODULE = "DISP&MM-FB"	
//$$ DEVICE = "mesonfb"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 4 ="reg"
//$$ L2 PROP_U32 = "vmode"
//$$ L2 PROP_U32 5 = "display_size_default"
//	mesonfb{
//		compatible = "amlogic,mesonfb";
//		dev_name = "mesonfb";
//		status = "okay";
//	   	reserve-memory = <0x01800000  0x00100000>;
//	   	reserve-iomap = "true";
//                vmode = <3>; /**0:VMODE_720P 1:VMODE_LCD  2:VMODE_LVDS_1080P 3:VMODE_1080P*/
//		scale_mode = <1>; /*0:default 1:new*/
//		4k2k_fb = <0>;
// 		display_size_default = <1920 1080 1920 3240 32>; //1920*1080*4*3 = 0x17BB000
//	};

//$$ DEVICE="deinterlace"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 2 = "reg"
//  deinterlace{
//		compatible = "amlogic,deinterlace";
//		dev_name = "deinterlace";
//		status = "ok";
//		reserve-memory = <0x02100000>; //10x1920x1088x3/2=33M
//	};

/// ***************************************************************************************
///	-	DISP&MM-A/V stream
//$$ MODULE = "DISP&MM-A/V stream"
//$$ DEVICE="mesonstream"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 4 ="reg"
//	mesonstream{
//		compatible = "amlogic,mesonstream";
//		dev_name = "mesonstream.0";
//		status = "okay";
//		reserve-memory = <0x02000000>; // 32M
//		reserve-iomap = "true";
//	};

/// ***************************************************************************************
///     -       DISP&MM-A/V stream
//$$ MODULE = "DISP&MM-A/V video dec"
//$$ DEVICE="vdec"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 4 ="reg"
//      vdec{
//              compatible = "amlogic,vdec";
//              dev_name = "vdec.0";
//              status = "okay";
//              reserve-memory = <0x04000000>; // 64M
//              reserve-iomap = "true";
//      };

/// ***************************************************************************************
///	-	DISP&MM-PostProcess
//$$ MODULE="DISP&MM-PostProcess"
//$$ DEVICE="ppmgr"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//  ppmgr{
//		compatible = "amlogic,ppmgr";
//		dev_name = "ppmgr";
//		status = "okay";
//		reserve-memory = <0x01000000>; // 16M
//	};

/// ***************************************************************************************
///	-	DISP&MM-AVC Video Encoder
//$$ MODULE = "DISP&MM-AVC Video Encoder"
//$$ DEVICE="amvenc_avc"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//  amvenc_avc{
//		compatible = "amlogic,amvenc_avc";
//		dev_name = "amvenc_avc.0";
//		status = "okay";
//		linux,contiguous-region = <&cma_0>;
//		reserve-iomap = "true";
//	};

/// ***************************************************************************************
///	-	DISP&MM-BT656
//$$ MODULE = "DISP&MM-BT656"
//$$ DEVICE="amvdec_656in"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 2 = "reg"
//    amvdec_656in{
//		compatible = "amlogic,amvdec_656in";
//		dev_name = "amvdec_656in";
//		status = "ok";
//		reg = <0x1e400000 0x00100000>;
//	};
//	
/// ***************************************************************************************
///	-	DISP&MM-VDIN
//$$ MODULE = "DISP&MM-VDIN"
//$$ DEVICE="vdin0"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 2 = "reg"
//$$ L2 PROP_U32 = "irq"
//$$ L2 PROP_U32 = "vdin_id"
//    vdin0{
//       compatible = "amlogic,vdin";
//        dev_name = "vdin0";
//        status = "ok";
//	 reserve-memory = <0x04000000>;
//        irq = <115>;
//        vdin_id = <0>;
//	};
	
//$$ DEVICE="vdin1"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 2 = "reg"
//$$ L2 PROP_U32 = "irq"
//$$ L2 PROP_U32 = "vdin_id"
//    vdin1{
//        compatible = "amlogic,vdin";
//       dev_name = "vdin1";
//        status = "ok";
//        reserve-memory = <0x01000000>;
//	  miracast_size = <1920 1080>;//1920x1080x2x4=17M
//	  reserve-iomap = "true";
//        irq = <117>;
//        vdin_id = <1>;
//	};

/// ***************************************************************************************
///	-	DISP&MM-AMLVIDEO2
//$$ MODULE = "DISP&MM-AMLVIDEO2"
//$$ DEVICE="amlvideo2"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//    amlvideo2{
//		compatible = "amlogic,amlvideo2";
//		dev_name = "amlvideo2.0";
//		status = "okay";
//		reserve-memory = <0x01800000>;
//		reserve-iomap = "true";
//	};

/// ***************************************************************************************
///	-	DISP&MM-Video Input Manager
//$$ MODULE = "DISP&MM-Video Input Manager"
//$$ DEVICE="vm"
//$$ L2 PROP_STR = "status"
//    vm{
//		compatible = "amlogic,vm";
//		dev_name = "vm.0";
//		status = "okay";
//		reserve-memory = <0x01800000>;
//		reserve-iomap = "true";
//	};

/// ***************************************************************************************
///	-	ION
//$$ MODULE="ION"
//$$ DEVICE="ion_dev"
//$$ L2 PROP_STR = "status"
    ion_dev{
        compatible = "amlogic,ion_dev";
        dev_name = "ion_dev";
        status = "ok";
        share-memory-name = "ppmgr0";
        share-memory-offset = <0>;
        share-memory-size = <0x01000000>; //16M
    };
/// ***************************************************************************************
///	-	DISP&MM-Vout
//$$ MODULE = "DISP&MM-Vout"
//$$ DEVICE = "mesonvout"
//$$ L2 PROP_STR = "status"
	mesonvout{
		compatible = "amlogic,mesonvout";
		dev_name = "mesonvout";
		status = "okay";
	};


	tvout {
		compatible = "amlogic,tvout";
		dev_name = "tvout";
		status = "okay";
	};

/// ***************************************************************************************
///	-	RTC
//$$ MODULE="RTC"
//$$ DEVICE="Rtc"
//$$ L2 PROP_STR = "status"
    rtc{
		compatible = "amlogic,aml_rtc";
		status = "okay";
	};

/// ***************************************************************************************
///	-	UART
//$$ MODULE="UART"
//$$ DEVICE="uart_ao"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR = "pinctrl-names"
//$$ L3 PROP_CHOICE "uart_ao_pin_match" = "pinctrl-0"
	uart_ao{
		compatible = "amlogic,aml_uart";
		port_name = "uart_ao";
		status = "okay";
		dev_name = "uart_ao";
		pinctrl-names = "default";
		pinctrl-0 = <&ao_uart_pins>;
	};
	
//$$ DEVICE="uart_0"
//$$ L2 PROP_STR = "status"
	uart_0{
		compatible = "amlogic,aml_uart";
		port_name = "uart_a";
		status = "okay";
		dev_name = "uart_0";
//    	pinctrl-names = "default";
//    	pinctrl-0 = <&a_uart_pins>;
	};
	
//$$ DEVICE="uart_1"
//$$ L2 PROP_STR = "status"
	uart_1{
		compatible = "amlogic,aml_uart";
		port_name = "uart_b";
		status = "okay";
		dev_name = "uart_1";
        pinctrl-names = "default";
        pinctrl-0 = <&b_uart_pins>;
	};
	
//$$ DEVICE="uart_2"
//$$ L2 PROP_STR = "status"
	uart_2{
		compatible = "amlogic,aml_uart";
		port_name = "uart_c";
		status = "disabled";
		dev_name = "uart_2";
	};
	
//$$ DEVICE="uart_3"
//$$ L2 PROP_STR = "status"	
	uart_3{
		compatible = "amlogic,aml_uart";
		port_name = "uart_d";
		status = "ok";
		dev_name = "uart_3";
	};

/// ***************************************************************************************
///	-	Bluetooth
//$$ MODULE="Bluetooth"
//$$ DEVICE="bt-dev"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR = "gpio_reset"
    bt-dev{
        compatible = "amlogic,bt-dev";
        dev_name = "bt-dev";
        status = "ok";
        gpio_reset = "GPIOX_20";
    };
/// ***************************************************************************************
///	-	WiFi
//$$ MODULE="WiFi"
//$$ DEVICE="aml_broadcm_wifi"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR = "interrupt_pin"
//$$ L2 PROP_U32 = "irq_num"
//$$ L2 PROP_STR = "irq_trigger_type"
//$$ L2 PROP_STR = "power_on_pin"
//$$ L2 PROP_STR = "clock_32k_pin"
    wifi{
		compatible = "amlogic,aml_broadcm_wifi";
		dev_name = "aml_broadcm_wifi";
		status = "okay";
		interrupt_pin = "GPIOX_21";
		irq_num = <4>;
		irq_trigger_type = "GPIO_IRQ_HIGH";
		power_on_pin = "GPIOAO_6";
		power_on_pin2 = "GPIOX_11";
		clock_32k_pin = "GPIOX_10";
	};
	
//$$ DEVICE="wifi_power"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR = "power_gpio"
	wifi_power{
            compatible = "amlogic,wifi_power";
            dev_name = "wifi_power";
            status = "okay";
            power_gpio = "GPIOAO_6";
            power_gpio2 = "GPIOX_11";
	}; 

/// ***************************************************************************************
///	-	MMC
//$$ MODULE="MMC"
//$$ DEVICE="aml_sdio"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//$$ L2 PROP_STR 7 = "pinctrl-names"
//$$ L2 PROP_CHOICE "sdio_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_CHOICE "sdio_pin_1_match" = "pinctrl-1"
//$$ L2 PROP_CHOICE "sdio_pin_2_match" = "pinctrl-2"
//$$ L2 PROP_CHOICE "sdio_pin_3_match" = "pinctrl-3"
//$$ L2 PROP_CHOICE "sdio_pin_4_match" = "pinctrl-4"
//$$ L2 PROP_CHOICE "sdio_pin_5_match" = "pinctrl-5"
//$$ L2 PROP_CHOICE "sdio_pin_6_match" = "pinctrl-6"
    sdio{
        compatible = "amlogic,aml_sdio";
        dev_name = "aml_sdio.0";
        status = "okay";
        reg = <0xc1108c20 0x20>;
        pinctrl-names = "sd_clk_cmd_pins", "sd_all_pins", "emmc_clk_cmd_pins", "emmc_all_pins", "sdio_clk_cmd_pins", "sdio_all_pins","sd_1bit_pins"; // "jtag_pin", "uartao_default";
        pinctrl-0 = <&sd_clk_cmd_pins>;
        pinctrl-1 = <&sd_all_pins>;
        pinctrl-2 = <&emmc_clk_cmd_pins>;
        pinctrl-3 = <&emmc_all_pins>;
        pinctrl-4 = <&sdio_clk_cmd_pins>;
        pinctrl-5 = <&sdio_all_pins>;
        pinctrl-6 = <&sd_1bit_pins>;

//$$ DEVICE="sd"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 = "port"
//$$ L2 PROP_STR = "pinname"
//$$ L3 PROP_U32 = "ocr_avail"
//$$ L2 PROP_STR 3 = "caps"
//$$ L3 PROP_U32 = "f_min"
//$$ L3 PROP_U32 = "f_max"
//$$ L3 PROP_U32 = "f_max_w"
//$$ L3 PROP_U32 = "max_req_size"
//$$ L2 PROP_STR = "gpio_dat3"
//$$ L2 PROP_STR = "jtag_pin"
//$$ L2 PROP_STR = "gpio_cd"
//$$ L2 PROP_STR = "gpio_ro"
//$$ L2 PROP_U32 = "irq_in"
//$$ L2 PROP_U32 = "irq_out"
//$$ L2 PROP_U32 = "card_type"
      sd{
            status = "okay";
            port = <1>;          /**0:sdio_a, 1:sdio_b, 2:sdio_c, 3:sdhc_a, 4:sdhc_b, 5:sdhc_c */
            pinname = "sd";
            ocr_avail = <0x200000>;          /**VDD voltage 3.3 ~ 3.4 */
            caps = "MMC_CAP_4_BIT_DATA","MMC_CAP_MMC_HIGHSPEED","MMC_CAP_SD_HIGHSPEED";
            f_min = <300000>;
            f_max = <50000000>;
            f_max_w = <50000000>;
            max_req_size = <0x20000>;          /**128KB*/
            gpio_dat3 = "CARD_4";
            jtag_pin = "CARD_0";
            gpio_cd = "CARD_6";
//            gpio_ro = "GPIODV_25";
            irq_in = <3>;
            irq_out = <5>;
            card_type = <5>; /* 0:unknown, 1:mmc card(include eMMC), 2:sd card(include tSD), 3:sdio device(ie:sdio-wifi), 4:SD combo (IO+mem) card, 5:NON sdio device(means sd/mmc card), other:reserved */
        };

//$$ DEVICE="emmc"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 = "port"
//$$ L2 PROP_STR = "pinname"
//$$ L3 PROP_U32 = "ocr_avail"
//$$ L2 PROP_STR 4 = "caps"
//$$ L3 PROP_U32 = "f_min"
//$$ L3 PROP_U32 = "f_max"
//$$ L3 PROP_U32 = "f_max_w"
//$$ L3 PROP_U32 = "max_req_size"
//$$ L2 PROP_STR = "gpio_dat3"
//$$ L2 PROP_U32 = "card_type"
//        emmc{
//            status = "ok";
//            port = <2>;          /**0:sdio_a, 1:sdio_b, 2:sdio_c, 3:sdhc_a, 4:sdhc_b, 5:sdhc_c */
//            pinname = "emmc";
//            ocr_avail = <0x200000>;          /**VDD voltage 3.3 ~ 3.4 */
//            caps = "MMC_CAP_4_BIT_DATA","MMC_CAP_MMC_HIGHSPEED","MMC_CAP_SD_HIGHSPEED", "MMC_CAP_NONREMOVABLE","MMC_CAP_ERASE", "MMC_CAP_HW_RESET"; // MMC_CAP_NEEDS_POLL -- for detect, MMC_CAP_NONREMOVABLE -- for eMMC/TSD
//            f_min = <300000>;
//            f_max = <50000000>;
//            f_max_w = <50000000>;
//            max_req_size = <0x20000>;          /**128KB*/
//            gpio_dat3 = "BOOT_3";
//            card_type = <1>; /* 0:unknown, 1:mmc card(include eMMC), 2:sd card(include tSD), 3:sdio device(ie:sdio-wifi), 4:SD combo (IO+mem) card, 5:NON sdio device(means sd/mmc card), other:reserved */
//        };

//$$ DEVICE="sdio"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 = "port"
//$$ L2 PROP_STR = "pinname"
//$$ L3 PROP_U32 = "ocr_avail"
//$$ L2 PROP_STR 4 = "caps"
//$$ L3 PROP_U32 = "f_min"
//$$ L3 PROP_U32 = "f_max"
//$$ L3 PROP_U32 = "max_req_size"
//$$ L2 PROP_U32 = "card_type"    
        sdio{
            status = "ok";
            port = <0>;          /*0:sdio_a, 1:sdio_b, 2:sdio_c, 3:sdhc_a, 4:sdhc_b, 5:sdhc_c */
            pinname = "sdio";
            ocr_avail = <0x200000>;          /*VDD voltage 3.3 ~ 3.4 */
            caps = "MMC_CAP_4_BIT_DATA","MMC_CAP_SDIO_IRQ","MMC_CAP_MMC_HIGHSPEED","MMC_CAP_SD_HIGHSPEED", "MMC_CAP_NONREMOVABLE";
            f_min = <300000>;
            f_max = <50000000>;
            max_req_size = <0x20000>;          /**128KB*/
            card_type = <3>; /* 0:unknown, 1:mmc card(include eMMC), 2:sd card(include tSD), 3:sdio device(ie:sdio-wifi), 4:SD combo (IO+mem) card, 5:NON sdio device(means sd/mmc card), other:reserved */
        };
    };

/// ***************************************************************************************
///	-	MMC
//$$ MODULE="MMC"
//$$ DEVICE="aml_sdhc"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//$$ L2 PROP_STR 6 = "pinctrl-names"
//$$ L2 PROP_CHOICE "sdhc_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_CHOICE "sdhc_pin_1_match" = "pinctrl-1"
//$$ L2 PROP_CHOICE "sdhc_pin_2_match" = "pinctrl-2"
//$$ L2 PROP_CHOICE "sdhc_pin_3_match" = "pinctrl-3"
//$$ L2 PROP_CHOICE "sdhc_pin_4_match" = "pinctrl-4"
//$$ L2 PROP_CHOICE "sdjc_pin_5_match" = "pinctrl-5"
// L2 PROP_CHOICE "sdhc_pin_6_match" = "pinctrl-6"
    sdhc{
        compatible = "amlogic,aml_sdhc";
        dev_name = "aml_sdhc.0";
        status = "okay";
        reg = <0xc1108e00 0x3c>;
        pinctrl-names = "sdhc_sd_clk_cmd_pins", "sdhc_sd_all_pins", "sdhc_emmc_clk_cmd_pins", "sdhc_emmc_all_pins", "sdhc_sdio_clk_cmd_pins", "sdhc_sdio_all_pins";
        pinctrl-0 = <&sdhc_sd_clk_cmd_pins>;
        pinctrl-1 = <&sdhc_sd_all_pins>;
        pinctrl-2 = <&sdhc_emmc_clk_cmd_pins>;
        pinctrl-3 = <&sdhc_emmc_all_pins>;
        pinctrl-4 = <&sdhc_sdio_clk_cmd_pins>;
        pinctrl-5 = <&sdhc_sdio_all_pins>;
        //pinctrl-6 = <&sd_1bit_pins>;

//$$ DEVICE="sd"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 = "port"
//$$ L2 PROP_STR = "pinname"
//$$ L3 PROP_U32 = "ocr_avail"
//$$ L2 PROP_STR 3 = "caps"
//$$ L3 PROP_U32 = "f_min"
//$$ L3 PROP_U32 = "f_max"
//$$ L3 PROP_U32 = "f_max_w"
//$$ L3 PROP_U32 = "max_req_size"
//$$ L2 PROP_STR = "gpio_dat3"
//$$ L2 PROP_STR = "jtag_pin"
//$$ L2 PROP_STR = "gpio_cd"
//$$ L2 PROP_STR = "gpio_ro"
//$$ L2 PROP_U32 = "irq_in"
//$$ L2 PROP_U32 = "irq_out"
//$$ L2 PROP_U32 = "card_type"
//         sd{
//             status = "okay";
//             port = <4>;          /**0:sdhc_a, 1:sdio_b, 2:sdio_c, 3:sdhc_a, 4:sdhc_b, 5:sdhc_c */
//             pinname = "sd";
//             ocr_avail = <0x00200080>; // 3.3:0x200000, 1.8+3.3:0x00200080
//             caps = "MMC_CAP_4_BIT_DATA","MMC_CAP_MMC_HIGHSPEED","MMC_CAP_SD_HIGHSPEED","MMC_CAP_UHS_SDR12","MMC_CAP_UHS_SDR25","MMC_CAP_UHS_SDR50","MMC_CAP_UHS_SDR104";
//             f_min = <300000>;
//             f_max = <100000000>;
//             max_req_size = <0x20000>;          /**128KB*/
//             gpio_dat3 = "CARD_4";
//             //jtag_pin = "CARD_0";
//             gpio_cd = "CARD_6";
//             //gpio_ro = "GPIOZ_0";
//             irq_in = <3>;
//             irq_out = <5>;
//             card_type = <5>; /* 0:unknown, 1:mmc card(include eMMC), 2:sd card(include tSD), 3:sdio device(ie:sdio-wifi), 4:SD combo (IO+mem) card, 5:NON sdio device(means sd/mmc card), other:reserved */
//         };

//$$ DEVICE="emmc"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 = "port"
//$$ L2 PROP_STR = "pinname"
//$$ L3 PROP_U32 = "ocr_avail"
//$$ L2 PROP_STR 4 = "caps"
//$$ L3 PROP_U32 = "f_min"
//$$ L3 PROP_U32 = "f_max"
//$$ L3 PROP_U32 = "f_max_w"
//$$ L3 PROP_U32 = "max_req_size"
//$$ L2 PROP_STR = "gpio_dat3"
//$$ L2 PROP_U32 = "card_type"
        emmc{
            status = "okay";
            port = <5>;          /**0:sdio_a, 1:sdio_b, 2:sdio_c, 3:sdhc_a, 4:sdhc_b, 5:sdhc_c */
            pinname = "emmc";
            ocr_avail = <0x200000>;          /**VDD voltage 3.3 ~ 3.4 */
            caps = "MMC_CAP_8_BIT_DATA","MMC_CAP_MMC_HIGHSPEED","MMC_CAP_SD_HIGHSPEED", "MMC_CAP_NONREMOVABLE","MMC_CAP_ERASE", "MMC_CAP_HW_RESET"; // MMC_CAP_NEEDS_POLL -- for detect, MMC_CAP_NONREMOVABLE -- for eMMC/TSD
            //caps2 = "MMC_CAP2_HS200_1_8V_SDR";
	        f_min = <300000>;
            f_max = <50000000>;
            max_req_size = <0x20000>;          /**128KB*/
            gpio_dat3 = "BOOT_3";
            card_type = <1>; /* 0:unknown, 1:mmc card(include eMMC), 2:sd card(include tSD), 3:sdio device(ie:sdio-wifi), 4:SD combo (IO+mem) card, 5:NON sdio device(means sd/mmc card), other:reserved */
        };

//$$ DEVICE="sdio"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 = "port"
//$$ L2 PROP_STR = "pinname"
//$$ L3 PROP_U32 = "ocr_avail"
//$$ L2 PROP_STR 4 = "caps"
//$$ L3 PROP_U32 = "f_min"
//$$ L3 PROP_U32 = "f_max"
//$$ L3 PROP_U32 = "max_req_size"    
//$$ L2 PROP_U32 = "card_type"    
        // sdio{
        //     status = "okay";
        //     port = <3>;          /**0:sdio_a, 1:sdio_b, 2:sdio_c, 3:sdhc_a, 4:sdhc_b, 5:sdhc_c */
        //     pinname = "sdio";
        //     ocr_avail = <0x00200080>; // 3.3:0x200000, 1.8+3.3:0x00200080
        //     caps = "MMC_CAP_4_BIT_DATA","MMC_CAP_MMC_HIGHSPEED","MMC_CAP_SD_HIGHSPEED", "MMC_CAP_NONREMOVABLE", "MMC_CAP_UHS_SDR12","MMC_CAP_UHS_SDR25","MMC_CAP_UHS_SDR50","MMC_CAP_UHS_SDR104";
        //     f_min = <300000>;
        //     f_max = <100000000>;
        //     max_req_size = <0x20000>;          /**128KB*/
        //     card_type = <3>; /* 0:unknown, 1:mmc card(include eMMC), 2:sd card(include tSD), 3:sdio device(ie:sdio-wifi), 4:SD combo (IO+mem) card, 5:NON sdio device(means sd/mmc card), other:reserved */
        // };
    };
    

/// ***************************************************************************************
///	-	I2C
//$$ MODULE="I2C"
//$$ DEVICE="I2C_AO"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//$$ L3 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "I2C_AO_pin_match" = "pinctrl-0"	
	i2c@c8100500{ /*I2C-AO*/
		compatible = "amlogic,aml_i2c";
		dev_name = "i2c-AO";
		status = "ok";
		reg = <0xc8100500 0x1d>;
		#address-cells = <1>;
		#size-cells = <0>;
		device_id = <0>;
		pinctrl-names="default";
		pinctrl-0=<&ao_i2c_master>;
		use_pio = <0>;
		master_i2c_speed = <100000>;
	};

//$$ DEVICE = "I2C_A"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//$$ L3 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "I2C_A_pin_match" = "pinctrl-0"
    i2c@c1108500{ /*I2C-A*/
		compatible = "amlogic,aml_i2c";
		dev_name = "i2c-A";
		status = "ok";
		reg = <0xc1108500 0x20>;
		device_id = <1>;
		pinctrl-names="default";
		pinctrl-0=<&a_i2c_master>;
		#address-cells = <1>;
		#size-cells = <0>;
		use_pio = <0>;
		master_i2c_speed = <300000>;
	};
	
//$$ DEVICE="I2C_B"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2="reg"
//$$ L3 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "I2C_B_pin_match" = "pinctrl-0"	
	i2c@c11087c0{ /*I2C-B*/
		compatible = "amlogic,aml_i2c";
		dev_name = "i2c-B";
		status = "ok";
		reg = <0xc11087c0 0x20>;
		device_id = <2>;
		pinctrl-names="default";
		pinctrl-0=<&b_i2c_master>;
		#address-cells = <1>;
		#size-cells = <0>;
		use_pio = <0>;
		master_i2c_speed = <300000>;
 	};

//$$ DEVICE="I2C_C"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2="reg"
//$$ L3 PROP_STR = "pinctrl-names"	
    i2c@c11087e0{ /*I2C-C*/
		compatible = "amlogic,aml_i2c";
		dev_name = "i2c-C";
		status = "ok";
		reg = <0xc11087e0 0x20>;
		device_id = <3>;
		pinctrl-names="default";
//		pinctrl-0=<&c_i2c_master>;
		#address-cells = <1>;
		#size-cells = <0>;
		use_pio = <0>;
		master_i2c_speed = <300000>;
	};

//$$ DEVICE="I2C_D"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2="reg"
//$$ L3 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "I2C_D_pin_match" = "pinctrl-0"	
	i2c@c1108d20{ /*I2C-D*/
		compatible = "amlogic,aml_i2c";
		dev_name = "i2c-D";
		status = "ok";
		reg = <0xc1108d20 0x20>;
		device_id = <4>;
		pinctrl-names="default";
		pinctrl-0=<&d_i2c_master>;
		#address-cells = <1>;
		#size-cells = <0>;
		use_pio = <0>;
		master_i2c_speed = <300000>;
	};

/// ***************************************************************************************
///	-	Power
//$$ MODULE="Power"
//$$ DEVICE="dvfs"
//$$ L2 PROP_STR = "status"
    dvfs {
        compatible = "amlogic, amlogic-dvfs";                   /** fixed for driver, don't change       */
        #address-cells = <1>;
        #size-cells = <0>;
        status = "ok";

//$$ L2 PROP_U32 = "dvfs_id"
//$$ L2 PROP_U32 = "table_count"
//$$ L2 PROP_U32 16*3 = "dvfs_table"
        vcck_dvfs {
            dvfs_id     = <1>;                                  /** must be value of (1 << n)            */
            table_count = <13>;                                 /** must be correct count for dvfs_table */
            dvfs_table  = <
            /* NOTE: frequent in this table must be ascending order */
            /* frequent(Khz)    min_uV      max_uV                  */
                  96000         860000      860000
                 192000         860000      860000
                 312000         860000      860000
                 408000         860000      860000
                 504000         860000      860000
                 600000         860000      860000
                 720000         860000      860000
                 816000         900000      900000
                1008000        1140000     1140000
                1200000        1140000     1140000
                1320000        1140000     1140000
                1488000        1140000     1140000
                1536000        1140000     1140000
            >;
        };
    };
//$$ DEVICE="meson_vcck_dvfs_driver"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "meson_vcck_dvfs_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_U32 = "use_pwm"
//$$ L2 PROP_U32 = "table_count"
//$$ L2 PROP_U32 16*2 = "cs_voltage_table"
	meson_vcck_dvfs_driver{
        compatible = "amlogic, meson_vcck_dvfs";
        dev_name = "meson_vcck_dvfs_driver";
        status = "ok";
        pinctrl-names = "default";
        pinctrl-0 = <&aml_pwm_pins>;
        use_pwm = <1>; 
        pmw_controller = "PWM_C";
        table_count = <29>;
        cs_voltage_table = <
        /*   
         * Note: This table is hardware depended, If your hardware use PWM method,
         * then first line in this table is PWM register value, second line is
         * voltage of VCCK according this PWM register value. If your platform use
         * constant-current source to adjust vcck voltage, then the first line should 
         * set to 0, means not valid, member 'use_pwm' in this node should set to 0.
         *
         *  ---- This table must be in ascending order by voltage ----
         *    
         *  PWM value       VCCK voltage 
         */ 
		0x1c0000        860000
		0x1b0001        870000
		0x1a0002        880000
		0x190003        890000		
		0x180004        900000			
		0x170005        910000
		0x160006        920000
		0x150007        930000
		0x140008        940000			
		0x130009        950000		
		0x12000a        960000			
		0x11000b        970000		
		0x10000c        980000			
		0x0f000d        990000			
		0x0e000e        1000000			
		0x0d000f        1010000		
		0x0c0010        1020000			
		0x0b0011        1030000			
		0x0a0012        1040000			
		0x090013        1050000
		0x080014        1060000
		0x070015        1070000			
		0x060016        1080000
		0x050017        1090000
		0x040018        1100000
		0x030019        1110000			
		0x02001a        1120000			
		0x01001b        1130000
		0x00001c        1140000
        >;   
    };   	

//$$ DEVICE="arm_pmu"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 4*3 = "interrupts"
    arm_pmu {
        compatible = "arm,cortex-a9-pmu";
        status = "ok";
        interrupts = <0     137     0x04
                      0     138     0x04
                      0     153     0x04
                      0     154     0x04>;
    };

/// ***************************************************************************************
///	-	USB Controller
//$$ MODULE="USB Controller"
    usb_con {
		lm-compatible = "logicmodule-bus";

//$$ DEVICE="usb_b"
//$$ L2 PROP_U32 = "lm-periph-id"
//$$ L2 PROP_STR = "clock-src"
//$$ L2 PROP_U32 = "port-id"
//$$ L2 PROP_U32 = "port-type"
//$$ L2 PROP_U32 = "port-speed"
//$$ L2 PROP_U32 = "port-config"
//$$ L2 PROP_U32 = "port-dma"
//$$ L2 PROP_U32 = "port-id-mode"
//$$ L2 PROP_STR = "status"
		usb_b{
			lm-compatible = "amlogic,usb";
			lm-periph-id = <1>; /** lm name */
			clock-src = "usb1"; /** clock src */
			port-id = <1>; /** ref to mach/usb.h */
			port-type = <1>;	/** 0: otg, 1: host, 2: slave */
			port-speed = <0>; /** 0: default, 1: high, 2: full */
			port-config = <0>; /** 0: default */
			port-dma = <0>; /** 0: default, 1: single, 2: incr, 3: incr4, 4: incr8, 5: incr16, 6: disable*/
			port-id-mode = <1>; /** 0: hardware, 1: sw_host, 2: sw_slave*/
                        fiq_use = <1>;
			status = "okay";
		};
		
//$$ DEVICE="usb_a"
//$$ L2 PROP_U32 = "lm-periph-id"
//$$ L2 PROP_STR = "clock-src"
//$$ L2 PROP_U32 = "port-id"
//$$ L2 PROP_U32 = "port-type"
//$$ L2 PROP_U32 = "port-speed"
//$$ L2 PROP_U32 = "port-config"
//$$ L2 PROP_U32 = "port-dma"
//$$ L2 PROP_U32 = "port-id-mode"
//$$ L2 PROP_STR = "gpio-vbus-power"
//$$ L2 PROP_U32 = "gpio-work-mask"
//$$ L2 PROP_STR = "status"
		usb_a{
			lm-compatible = "amlogic,usb";
			lm-periph-id = <0>; /** lm name */
			clock-src = "usb0"; /** clock src */
			port-id = <0>;  /** ref to mach/usb.h */
			port-type = <1>;	/** 0: otg, 1: host, 2: slave */
			port-speed = <0>; /** 0: default, high, 1: full */
			port-config = <0>; /** 0: default */
			port-dma = <0>; /** 0: default, 1: single, 2: incr, 3: incr4, 4: incr8, 5: incr16, 6: disable*/
			port-id-mode = <0>; /** 0: hardware, 1: sw_host, 2: sw_slave*/
//			gpio-vbus-power = "GPIOZ_1";
			gpio-work-mask	= <1>; /**0: work on pulldown,1:work on pullup*/
			status = "okay";
		};
	};


/// ***************************************************************************************
/// -   Audio
//$$ MODULE="Audio"
//$$ DEVICE="audio_i2s"
//$$ L2 PROP_STR = "status"
    audio_platform{
        compatible = "amlogic,aml-i2s";
        dev_name = "aml-i2s.0";
        status = "okay";
    };

//$$ DEVICE="audio_i2s_dai"
//$$ L2 PROP_STR = "status"
    audio_dai{
        compatible = "amlogic,aml-i2s-dai";
        dev_name = "aml-i2s-dai.0";
        status = "okay";
    };
    audio_spdif_dai{
        compatible = "amlogic,aml-spdif-dai";
        dev_name = "aml-spdif-dai.0";
        status = "okay";
    };

    audio_spdif_codec{
        compatible = "amlogic,aml-spdif-codec";
        dev_name = "spdif-dit.0";
        status = "okay";
    };

//$$ DEVICE="audio_pcm2BT_codec"
//$$ L2 PROP_STR = "status"
    audio_pcm2BT_codec{
        compatible = "amlogic,pcm2BT-codec";
        dev_name = "pcm2bt.0";
        status = "okay";
    };

//$$ DEVICE="audio_pcm_dai"
//$$ L2 PROP_STR = "status"
    audio_pcm_dai{
        compatible = "amlogic,aml-pcm-dai";
        dev_name = "aml-pcm-dai.0";
        status = "okay";
    };

//$$ DEVICE="audio_pcm"
//$$ L2 PROP_STR = "status"
    audio_pcm{
        compatible = "amlogic,aml-pcm";
        dev_name = "aml-pcm.0";
        status = "okay";
    };

//$$ DEVICE="audio_m8_audio"
//$$ L2 PROP_STR = "status"
    audio_m8_audio{
        compatible = "amlogic,m8_audio_codec";
        dev_name = "aml_m8_codec.0";
        status = "disable";
    };

//$$ DEVICE="dummy_codec"
//$$ L2 PROP_STR = "status"
    dummy_codec{
        compatible = "amlogic,aml_dummy_codec";
        dev_name = "dummy_codec.0";
        status = "okay";
    };

    aml_audio_codec{
        compatible = "amlogic,audio_codec";
        rt5616:rt5616{
            codec_name = "rt5616";
            i2c_addr = <0x1B>;
            i2c_bus = "i2c_bus_d";
            id_reg = <0x00>;
            id_val = <0x21>;
            capless = <0>;
            status = "disable";
        };
        rt5631:rt5631{
            codec_name = "rt5631";
            i2c_addr = <0x1A>;
            i2c_bus = "i2c_bus_b";
            id_reg = <0x00>;
            id_val = <0x01>;
            capless = <0>;
            status = "disable";      
        };  
        wm8960:wm8960{
            codec_name = "wm8960";
            i2c_addr = <0x1A>;
            i2c_bus = "i2c_bus_b";
            capless = <1>;
            status = "disable";
        };

        dummy:dummy{
          codec_name = "dummy_codec";
          status = "okay";
        };
    };

//$$ DEVICE="aml_m8_sound_card"
//$$ L2 PROP_STR = "aml,sound_card"
//$$ L2 PROP_STR = "aml,codec_dai"
//$$ L2 PROP_STR 6*2 = "aml,audio-routing"
//$$ L2 PROP_STR = "mute_gpio"
//$$ L2 PROP_U32 5 = "hp_paraments"
//$$ L2 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "Audio_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_STR = "status"
    aml_m8_sound_card{
        compatible = "sound_card, aml_snd_m8";
        aml,sound_card = "AML-M8AUDIO";
        aml,codec_dai = "AML-M8","rt5616-aif1","rt5631-hifi","wm8960-hifi","dummy_codec";
        //aml,codec_name = "aml_m8_codec.0","rt5616.4-001b";
        //aml,audio-codec = <&rt5616>;
        aml,audio-routing-rt5616 = 
            "Ext Spk","LOUTL",
            "Ext Spk","LOUTR",
            "HP","HPOL",
            "HP","HPOR",
            "micbias1","MAIN MIC",
            "IN2P","micbias1";
        aml,audio-routing-amlm8 = 
            "Ext Spk","LINEOUTL",
            "Ext Spk","LINEOUTR",
            "HP","HP_L",
            "HP","HP_R",
            "MICBIAS","MAIN MIC",
            "LINPUT1","MICBIAS";
        aml,audio-routing-dummy=
            "Ext Spk","LOUTL",
            "Ext Spk","LOUTR";
        mute_gpio = "GPIO_BSD_EN";
        hp_disable;
        //mute_inv;
        hp_paraments = <800 300 0 5 1>;
        pinctrl-names = "aml_snd_m8";
        pinctrl-0 = <&audio_pins>;
        status = "okay";
        
    };

/// ***************************************************************************************
///	-	Camera
//$$ MODULE="Camera"
///	-	aml_cams
//$$ DEVICE = "aml_cams"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR 2 = "pinctrl-names"
//$$ L2 PROP_CHOICE "Camera_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_CHOICE "Camera_pin_1_match" = "pinctrl-1"
	aml_cams{
		compatible = "amlogic,cams_prober";
		status = "okay";
		pinctrl-names = "gpio","csi";
		pinctrl-0 = <&aml_cam_gpio_pins> ;
		pinctrl-1 = <&aml_cam_csi_pins> ;

///	-	ar0543
//$$ DEVICE="ar0543"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 = "front_back"
//$$ L2 PROP_STR = "i2c_bus"
//$$ L2 PROP_STR = "gpio_pwdn"
//$$ L2 PROP_STR = "gpio_rst"
//$$ L2 PROP_U32 = "mirror_flip"
//$$ L2 PROP_U32 = "vertical_flip"
//$$ L2 PROP_STR = "config_path"
//$$ L2 PROP_U32 = "mclk"
//$$ L2 PROP_STR = "bt_path"
//$$ L2 PROP_STR = "interface"
//$$ L2 PROP_STR = "clk_channel"
		cam_0{
			cam_name = "ar0543";
			front_back = <0>;
			i2c_bus = "i2c_bus_d";
			gpio_pwdn = "GPIOH_6";
			gpio_rst = "GPIOH_4";
			mirror_flip = <0>;
			vertical_flip = <0>;
			config_path = "/system/etc/camera_isp_cfg/ar0543_skt";
			mclk = <12000>;
			bt_path = "csi";
			interface = "mipi";
			clk_channel = "a";
			status = "okay";
		};

///	-	ov5647
//$$ DEVICE="ov5647"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 = "front_back"
//$$ L2 PROP_STR = "i2c_bus"
//$$ L2 PROP_STR = "gpio_pwdn"
//$$ L2 PROP_STR = "gpio_rst"
//$$ L2 PROP_U32 = "mirror_flip"
//$$ L2 PROP_U32 = "vertical_flip"
//$$ L2 PROP_STR = "bt_path"
//$$ L2 PROP_STR = "interface"
//$$ L2 PROP_STR = "clk_channel"
		cam_1{
			cam_name = "ov5647";
			front_back = <0>;
			i2c_bus = "i2c_bus_d";
			gpio_pwdn = "GPIOH_5";
			gpio_rst = "GPIOH_4";
			mirror_flip = <0>;
			vertical_flip = <0>;	
			config_path = "/system/etc/camera_isp_cfg/ov5647_cw0767";
			bt_path = "csi";
			interface = "mipi";
			clk_channel = "b";
			status = "okay";
		};
		
		cam_2{
			cam_name = "ar0833";
			front_back = <0>;
			i2c_bus = "i2c_bus_d";
			gpio_pwdn = "GPIOH_6";
			gpio_rst = "GPIOH_4";
			mirror_flip = <0>;
			vertical_flip = <0>;
			config_path = "/system/etc/camera_isp_cfg/ar0833_skt";
			mclk = <12000>;
			bt_path = "csi";
			interface = "mipi";
			clk_channel = "a";
			status = "okay";
		};
	};	

/// ***************************************************************************************
///	-	Input
//$$ MODULE="Input"
//$$ DEVICE="gpio_keypad"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 = "scan_period"
//$$ L2 PROP_U32 = "key_num"
//$$ L2 PROP_STR = "key_name"
//$$ L2 PROP_U32 = "key_code"
//$$ L2 PROP_STR = "key_pin"
//$$ L2 PROP_U32 = "irq_keyup"
//$$ L2 PROP_U32 = "irq_keydown"
    gpio_keypad{
		compatible = "amlogic,gpio_keypad";
		status = "okay";
		scan_period = <20>;
		key_num = <1>;
        key_name = "power";
		key_code = <116>;
		key_pin = "GPIOAO_3";
        irq_keyup = <6>;
        irq_keydown = <7>;
	};
//$$ DEVICE="saradc"
//$$ L2 PROP_STR = "status"
	saradc{
		compatible = "amlogic,saradc";
		status = "okay";
	};

//$$ DEVICE="adc_keypad"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_STR = "key_name"
//$$ L2 PROP_U32 = "key_num"
//$$ L2 PROP_U32 2 = "key_code"
//$$ L2 PROP_U32 2 = "key_chan"
//$$ L2 PROP_U32 2 = "key_val"
//$$ L2 PROP_U32 2 = "key_tolerance"
/*    adc_keypad{
		compatible = "amlogic,adc_keypad";
		status = "okay";
		key_name = "menu", "vol-","vol+", "esc", "home";
		key_num = <5>;
		key_code = <139 114 115 1 102>;
		key_chan = <0 0 0 0 0>;
		key_val = <0 143 271 393 468>; //voltage=0/252/478/692/824mV, val=voltage/1800mV*1023
		key_tolerance = <40 40 40 40 40>;
	};
*/

//$$ DEVICE="meson-remote"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 = "ao_baseaddr"
//$$ L2 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "remote_pin_0_match" = "pinctrl-0"
    meson-remote{
		compatible = "amlogic,aml_remote";
		dev_name = "meson-remote";
		status = "ok";
		ao_baseaddr = <0xf3100480>;
		pinctrl-names="default";
		pinctrl-0=<&remote_pins>;
	};

/// ***************************************************************************************
///	-	Spi
//$$ MODULE="Spi"
//$$ DEVICE="spi"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 2 = "reg"
//$$ L2 PROP_STR = "pinctrl-names"
//$$ L2 PROP_CHOICE "Spi_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_U32 = "nr-parts"
//$$ L2 PROP_CHOICE "Spi_nr-part-0_match" = "nr-part-0"
//$$ L2 PROP_CHOICE "Spi_nr-part-1_match" = "nr-part-1"
    spi@cc000000{
		compatible = "amlogic,apollo_spi_nor";
		status = "ok";
		reg = <0xcc000000 0x04000000>;
		pinctrl-names = "default";
		pinctrl-0 = <&aml_spi_nor_pins>;

		nr-parts = <2>;
		nr-part-0 = <&bootloader>;
		nr-part-1 = <&ubootenv>;

//$$ MATCH "Spi_nr-part-0_match" = <&bootloader>
//$$ L2 PROP_STR = "name"
//$$ L2 PROP_U32 = "offset"
//$$ L2 PROP_U32 = "size"
		bootloader:bootloader{
			name = "bootloader";
			offset = <0>;
			size = <0x100000>;
		};

//$$ MATCH "Spi_nr-part-1_match" = <&ubootenv>
//$$ L2 PROP_STR = "name"
//$$ L2 PROP_U32 = "offset"
//$$ L2 PROP_U32 = "size"
		ubootenv:ubootenv{
			name = "ubootenv";
		      offset = <0x100000>;
		      size = <0x10000>;
		};
	};
	
/// ***************************************************************************************
///	-	Nand
//$$ MODULE="Nand"
//$$ DEVICE="aml_nand"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 2 ="reg"
//$$ L2 PROP_STR 2 = "pinctrl-names"
//$$ L2 PROP_CHOICE 3 "Nand_pin_0_match" = "pinctrl-0"
//$$ L2 PROP_CHOICE 3 "Nand_pin_1_match" = "pinctrl-1"
//$$ L3 PROP_STR ="plat-names"
//$$ L2 PROP_U32 = "plat-num"
//$$ L2 PROP_CHOICE "plat-part-0_match" = "plat-part-0"
	nand{
		compatible = "amlogic,aml_nand";
		dev_name = "nand";
		status = "ok";
		reg = <0xd0048600 0x24>;
		pinctrl-names = "nand_rb_mod","nand_norb_mod";
		pinctrl-0 = <&nand_input_state &conf_nand_state &conf_nand_state1 &nand_base>;
		pinctrl-1 = <&nand_input_state &conf_nand_state &conf_nand_state1 &nand_base>;
		device_id = <0>;
		plat-names = "nandnormal";
		plat-num = <1>;
		plat-part-0 = <&normal>;

//$$ MATCH "plat-part-0_match" = <&normal>
//$$ L2 PROP_STR 4 = "enable_pad"
//$$ L2 PROP_STR = "busy_pad"
		normal: normal{
			enable_pad ="ce0","ce1","ce2","ce3";
			busy_pad = "rb0";
		};
	};

/// ***************************************************************************************
///	-	Efuse
//$$ MODULE="Efuse"
//$$ DEVICE="efuse"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_U32 2 = "plat-pos"
//$$ L2 PROP_U32 = "plat-count"
//$$ L2 PROP_U32 = "usid-min"
//$$ L2 PROP_U32 = "usid-max"
    efuse{
		compatible = "amlogic,efuse";
		dev_name = "efuse";
		status = "okay";
		plat-pos = <0 454>;
		plat-count = <58>;
		usid-min = <8>; /*reserved*/
		usid-max = <31>; /*reserved*/
	};
	
/// ***************************************************************************************
///	-	Thermal
//$$ MODULE="Thermal"
//$$ DEVICE="thermal"
//$$ L2 PROP_U32 3*3 = "trip_point"
//$$ L2 PROP_U32 = "#thermal-cells"
//$$ L2 PROP_U32 = "cpu_cali_a"
//$$ L2 PROP_U32 = "idle_interval"
	thermal{
		compatible = "amlogic-thermal";
		#thermal-cells=<7>;
		dev_name = "aml_thermal";
        trip_point=<70 1488001 1488001 511 511 3 2
                    80 1206001 1206001 435 435 2 2
                    90  804001  804001 328 328 1 1
                    260 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff>;
		cpu_cali_a=<0>;
		idle_interval=<1000>;
        use_virtual_thermal;
        freq_sample_period=<30>;
        report_time=<1 10 30 60>;         /* based on freq_sample_period */
        cpu_virtual=<
             500000  40  40  40  40
             600000  45  55  60  65
             800000  50  60  65  70
            1000000  55  65  70  75
            1200000  60  70  75  80
            1350000  65  75  80  85
        >;
        gpu_virtual=<
            183      40  40  40  40
            251      40  45  50  55
            319      50  60  65  70
            426      55  65  70  75
            511      60  70  75  80
        >;
	};
	
/// ***************************************************************************************
///	-	Securitykey
//$$ MODULE="Securitykey"
//$$ DEVICE="securitykey"
//$$ L2 PROP_STR = "status"
    securitykey{
		compatible = "amlogic,aml_keys";
		status = "ok";
	};

/// ***************************************************************************************
///	-	Unifykey
//$$ MODULE="Unifykey"
//$$ DEVICE="securitykey"
//$$ L2 PROP_STR = "status"
//$$ L3 PROP_U32 ="unifykey-num"
//$$ L2 PROP_CHOICE "Unifykey_0_match" = "unifykey-index-0"
//$$ L2 PROP_CHOICE "Unifykey_1_match" = "unifykey-index-1"
//$$ L2 PROP_CHOICE "Unifykey_2_match" = "unifykey-index-2"
    	unifykey{
		compatible = "amlogic,unifykey";
		status = "ok";

		/*efuse-version = <20>;*/ /*m6 efuse version 2,m3 efuse version 1, not config efuse version in default*/
		unifykey-num = <6>;
		unifykey-index-0 = <&keysn_0>;
		unifykey-index-1 = <&keysn_1>;
		unifykey-index-2 = <&keysn_2>;
		unifykey-index-3 = <&keysn_3>;
		unifykey-index-4 = <&keysn_4>;
		unifykey-index-5 = <&keysn_5>;


//$$ MATCH "Unifykey_0_match" = <&keysn_0>
//$$ L2 PROP_STR = "key-name"
//$$ L2 PROP_STR = "key-device"
//$$ L2 PROP_STR = "key-dataformat"
//$$ L2 PROP_STR 3 = "key-permit"
		keysn_0: key_0{
			key-name = "usid";
			key-device = "nandkey";
			key-dataformat = "allascii";
			key-permit = "read","write","del";
		};
		
//$$ MATCH "Unifykey_1_match" = <&keysn_1>
//$$ L2 PROP_STR = "key-name"
//$$ L2 PROP_STR = "key-device"
//$$ L2 PROP_STR = "key-dataformat"
//$$ L2 PROP_STR 3 = "key-permit"
		keysn_1:key_1{
			key-name = "mac";
			key-device = "nandkey";
			key-dataformat = "hexdata";
			key-permit = "read","write","del";
		};
		
//$$ MATCH "Unifykey_2_match" = <&keysn_2>
//$$ L2 PROP_STR = "key-name"
//$$ L2 PROP_STR = "key-device"
//$$ L2 PROP_STR = "key-dataformat"
//$$ L2 PROP_STR 3 = "key-permit"
		keysn_2:key_2{
			key-name = "hdcp";
			key-device = "nandkey";
			key-dataformat = "hexdata";
			key-permit = "read","write","del";
		};

//$$ MATCH "Unifykey_3_match" = <&keysn_3>
//$$ L2 PROP_STR = "key-name"
//$$ L2 PROP_STR = "key-device"
//$$ L2 PROP_STR = "key-dataformat"
//$$ L2 PROP_STR 3 = "key-permit"
		keysn_3:key_3{
			key-name = "secure_boot_set";
			key-device = "efusekey";
			key-dataformat = "hexdata";
			key-permit = "read","write";
		};
		
//$$ MATCH "Unifykey_4_match" = <&keysn_4>
//$$ L2 PROP_STR = "key-name"
//$$ L2 PROP_STR = "key-device"
//$$ L2 PROP_STR = "key-dataformat"
//$$ L2 PROP_STR 3 = "key-permit"
		keysn_4:key_4{
			key-name = "mac_bt";
			key-device = "nandkey";
			key-dataformat = "hexdata";
			key-permit = "read","write","del";
		};
		
//$$ MATCH "Unifykey_5_match" = <&keysn_5>
//$$ L2 PROP_STR = "key-name"
//$$ L2 PROP_STR = "key-device"
//$$ L2 PROP_STR = "key-dataformat"
//$$ L2 PROP_STR 3 = "key-permit"
		keysn_5:key_5{
			key-name = "mac_wifi";
			key-device = "nandkey";
			key-dataformat = "hexdata";
			key-permit = "read","write","del";
		};
	};

/// ***************************************************************************************
///	-	HDMI
//$$ MODULE="HDMI"
//$$ DEVICE="amhdmitx"
//$$ L2 PROP_STR = "status"
//$$ L2 PROP_CHOICE "HDMI_vend-data_match" = "vend-data"
//$$ L2 PROP_CHOICE "HDMI_pwr-ctrl_match" = "pwr-ctrl"
    amhdmitx{
		compatible = "amlogic,amhdmitx";
		dev_name = "amhdmitx";
		status = "ok";
        vend-data = <&vend_data>;
        pwr-ctrl = <&pwr_ctrl>;
        
//$$ MATCH "HDMI_vend-data_match" = <&vend_data>
//$$ L2 PROP_STR = "vendor_name"
//$$ L2 PROP_U32 = "vendor_id"
//$$ L2 PROP_STR = "product_desc"
//$$ L2 PROP_STR = "cec_osd_string"   
//$$ L2 PROP_U32 = "cec_config"    
//$$ L2 PROP_U32 = "ao_cec"   
        vend_data: vend_data{
            vendor_name = "Amlogic";           /* Max Chars: 8     */
            vendor_id = <0x000000>;            /* Refer to http://standards.ieee.org/develop/regauth/oui/oui.txt */
            product_desc = "M8 MBox SKTv1";    /* Max Chars: 16    */
            cec_osd_string = "MBox";           /* Max Chars: 14    */
            cec_config = <0x00000f>;           /* 4 bytes: use to control cec switch on/off; distinguish between Mbox and Tablet. <0x00000f>:Mbox; <0x000000> or no this value:Tablet*/
            ao_cec = <0x000001>;               /* switch between ao-cec and ee-cec:: 1: ao-cec; 0: ee-cec */
        };
        
//$$ MATCH "HDMI_pwr-ctrl_match" = <&pwr_ctrl>
//$$ L2 PROP_STR = "pwr_5v_on"
//$$ L2 PROP_STR = "pwr_5v_off"
//$$ L2 PROP_STR = "pwr_3v3_on"
//$$ L2 PROP_STR = "pwr_3v3_off"
//$$ L2 PROP_STR = "pwr_hpll_vdd_on"
//$$ L2 PROP_STR = "pwr_hpll_vdd_off"
        pwr_ctrl: pwr_ctrl{
            pwr_5v_on = "";
            pwr_5v_off = "";
            pwr_3v3_on = "";
            pwr_3v3_off = "";
            pwr_hpll_vdd_on = "";
            pwr_hpll_vdd_off = "";
        };
	};

/// ***************************************************************************************
///	-	PowerManager
//$$ MODULE="PowerManager"
//$$ DEVICE="amvenc_avc"
//$$ L2 PROP_STR = "status"
    aml_pm{
		compatible = "amlogic,pm-m8";
		dev_name = "aml_pm_m8";
		status = "okay";
	};

/// ***************************************************************************************
///	-	Cpufreq
//$$ MODULE="Cpufreq"
//$$ DEVICE="cpufreq-meson"
//$$ L2 PROP_STR = "status"
    cpufreq-meson{
        compatible = "amlogic,cpufreq-meson";
        syspll_fixed;
        fixpll_target = <1536000>;
        status = "okay";
    };

//    crypto_device{
//       compatible = "amlogic,crypto-device";
//       dev_name = "crypto_device";
//    };

/// **************************************************************************************
/// -   GPIO
//$$ MODULE="GPIO"
//$$ DEVICE="m8-gpio"
	gpio:gpio{
		compatible = "amlogic,m8b-gpio";
		dev_name = "gpio";
		#gpio-cells=<2>;
	};

/// **************************************************************************************
/// -   Pinmux
//$$ MODULE="Pinmux"
//$$ DEVICE="pinmux-m8"
    pinmux{ 
		compatible = "amlogic,pinmux-m8b";
		dev_name = "pinmux";
		#pinmux-cells=<2>;    
    
//$$ MATCH "uart_ao_pin_match" = "&ao_uart_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
        ao_uart_pins:ao_uart{
			amlogic,setmask=<10 0x1800>;
			amlogic,pins="GPIOAO_0", "GPIOAO_1";
		};
		
//$$ MATCH "uart_0_pin_match" = "&a_uart_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_STR 4 = "amlogic,pins"
//		a_uart_pins:a_uart{
//			amlogic,setmask=<4 0x3c00>;
//			amlogic,pins="GPIOX_12", "GPIOX_13", "GPIOX_14", "GPIOX_15";
//		};

//$$ MATCH "uart_1_pin_match" = "&b_uart_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_STR 4 = "amlogic,pins"
		b_uart_pins:b_uart{
			amlogic,setmask=<4 0x03c0>;
			amlogic,pins="GPIOX_16", "GPIOX_17", "GPIOX_18", "GPIOX_19";
		};
		
//$$ MATCH "Nand_pin_0_match" = "&nand_input_state"
//$$ MATCH "Nand_pin_1_match" = "&nand_input_state"
//$$ L2 PROP_STR 18 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
		nand_input_state:nand_input{
			amlogic,pins = "BOOT_0","BOOT_1","BOOT_2","BOOT_3","BOOT_4",
						"BOOT_5","BOOT_6","BOOT_7","BOOT_12","BOOT_13",
						"BOOT_8","BOOT_9","BOOT_10","BOOT_11",
						"BOOT_14","BOOT_15","BOOT_16","BOOT_17";
			amlogic,enable-output=<1>;
		};
		
//$$ MATCH "Nand_pin_0_match" = "&conf_nand_state"
//$$ MATCH "Nand_pin_1_match" = "&conf_nand_state"
//$$ L2 PROP_STR 9 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,pullup"
		conf_nand_state: conf_nand{
			amlogic,pins = "BOOT_0","BOOT_1","BOOT_2","BOOT_3","BOOT_4",
						"BOOT_5","BOOT_6","BOOT_7","BOOT_15";
			amlogic,pullup=<0>;
			amlogic,pullupen=<1>;
		};
		conf_nand_state1: conf_nand1{
			amlogic,pins = "BOOT_8", "BOOT_10";
			amlogic,pullup=<1>;
			amlogic,pullupen=<1>;
		};
//$$ MATCH "Nand_pin_0_match" = "&nand_base"
//$$ MATCH "Nand_pin_1_match" = "&nand_base"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 17 = "amlogic,pins"
		nand_base: nand{
			amlogic,setmask=<2 0x7fe0000>;
			amlogic,clrmask=<	5 0xe
							6 0x3f000000
							4 0x7c000000>;
			amlogic,pins = "BOOT_0","BOOT_1","BOOT_2","BOOT_3","BOOT_4",
						"BOOT_5","BOOT_6","BOOT_7","BOOT_8","BOOT_9",
						"BOOT_10","BOOT_12","BOOT_13",
						"BOOT_14","BOOT_15","BOOT_16","BOOT_17";
		};
		
//$$ MATCH "Card_pin_0_match" = "&sdhc_b_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 4 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"	
		sdhc_b_pins:sdhc_b_pin{
			amlogic,setmask=<2 0xfc00>;
			amlogic,clrmask=<2 0xf0 8 0x600>;
			amlogic,pins="CARD_0","CARD_1","CARD_2","CARD_3","CARD_4","CARD_5";
		};

//$$ MATCH "Card_pin_1_match" = "&sdhc_c_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 4 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"	
		sdhc_c_pins:sdhc_c_pin{
			amlogic,setmask=<6 0x3f000000>;
			amlogic,clrmask=<4 0x6c000000 2 0x4c00000>;
			amlogic,pins="BOOT_0","BOOT_1","BOOT_2","BOOT_3","BOOT_10","BOOT_11";
		};

//$$ MATCH "Card_pin_2_match" = "&sdhc_a_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"		
		sdhc_a_pins:sdhc_a_pin{
			amlogic,setmask=<8 0x3f>;
			amlogic,clrmask=<5 0x6c00 >;
			amlogic,pins="GPIOX_0","GPIOX_1","GPIOX_2","GPIOX_3","GPIOX_8","GPIOX_9";
		};

//$$ MATCH "sdio_pin_5_match" = "&sdio_all_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"	
        sdio_all_pins:sdio_all_pins{
            amlogic,setmask=<8 0x0000003f>;         /*sdio a*/
            amlogic,clrmask=<6 0x3f000000           /*sdio c*/
                                2 0x0000fc00        /*sdio b*/
                                5 0x00006c00>;      /*sdhc a*/
            amlogic,pins = "GPIOX_0","GPIOX_1","GPIOX_2","GPIOX_3","GPIOX_8","GPIOX_9";
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
        
//$$ MATCH "sdio_pin_4_match" = "&sdio_clk_cmd_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdio_clk_cmd_pins:sdio_clk_cmd_pins{
            amlogic,setmask=<8 0x00000003>;         /*sdio a*/
            amlogic,clrmask=<6 0x3f000000           /*sdio c*/
                                2 0x0000fc00        /*sdio b*/
                                5 0x00006c00>;      /*sdhc a*/
            amlogic,pins = "GPIOX_8","GPIOX_9"; /** GPIOX_8:CLK, GPIOX_9:CMD */
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };

//$$ MATCH "sdio_pin_1_match" = "&sd_all_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sd_all_pins:sd_all_pins{
            amlogic,setmask=<2 0x0000fc00>;         /*sdio b*/
            amlogic,clrmask=<6 0x3f000000           /*sdio c*/
                                8 0x0000063f        /*sdio a, UART*/
                                2 0x000000f0>;      /*sdhc b*/
            amlogic,pins = "CARD_0","CARD_1","CARD_2","CARD_3","CARD_4","CARD_5";
            amlogic,enable-output=<1>; /* 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
        
//$$ MATCH "sdio_pin_6_match" = "&sd_1bit_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sd_1bit_pins:sd_1bit_pins{
            amlogic,setmask=<2 0x00008c00>;         /*sdio b*/
            amlogic,clrmask=<6 0x3f000000           /*sdio c*/
                                8 0x0000003f        /*sdio a*/
                                2 0x000000f0>;      /*sdhc b*/
            amlogic,pins = "CARD_0","CARD_1","CARD_2","CARD_3","CARD_4","CARD_5";
            amlogic,enable-output=<1>; /* 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
        
//$$ MATCH "sdio_pin_0_match" = "&sd_clk_cmd_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sd_clk_cmd_pins:sd_clk_cmd_pins{
            amlogic,setmask=<2 0x00000c00>;         /*sdio b*/
            amlogic,clrmask=<6 0x3f000000           /*sdio c*/
                                8 0x0000003f        /*sdio a*/
                                2 0x000000f0>;      /*sdhc b*/
            amlogic,pins = "CARD_2","CARD_3"; /** CARD_2:CLK, CARD_3:CMD */
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
        
//$$ MATCH "sdio_pin_3_match" = "&emmc_all_pins"  
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"      
        emmc_all_pins:emmc_all_pins{
            amlogic,setmask=<6 0xfc000000>;         /*sdio c*/
            amlogic,clrmask=<2 0x06c2fc00           /*sdio b & nand*/
                                8 0x0000003f        /*sdio a*/
                                4 0x6c000000>;        /*sdhc c*/
            amlogic,pins = "BOOT_0","BOOT_1","BOOT_2","BOOT_3","BOOT_8","BOOT_10";
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
        
//$$ MATCH "sdio_pin_2_match" = "&emmc_clk_cmd_pins" 
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"	
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        emmc_clk_cmd_pins:emmc_clk_cmd_pins{
            amlogic,setmask=<6 0xc0000000>;         /*bit[30-31] */
            amlogic,clrmask=<2 0x06c2fc00           /*sdio b & nand   nand bit17 bit25*/ 
                                8 0x0000003f        /*sdio a*/
                                7 0xc0000>;        /*sdhc c bit 18-19*/
            amlogic,pins = "BOOT_8","BOOT_10"; /** BOOT_10:CMD, BOOT_8:CLK */
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };

//$$ MATCH "sdhc_pin_0_match" = "&sdhc_sd_clk_cmd_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 4*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdhc_sd_clk_cmd_pins:sdhc_sd_clk_cmd_pins{
            amlogic,setmask=<2 0x00000030>;         /*sdhc b*/
            amlogic,clrmask=<5 0x00007c00           /*sdhc a*/
                                4 0x7c000000        /*sdhc c*/
                                2 0x0000fc00        /*sdio b*/
                                8 0x00000600>;      /*UART*/
            amlogic,pins = "CARD_2","CARD_3"; /* CARD_2:CLK, CARD_3:CMD */
            amlogic,enable-output=<1>; /* 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
//$$ MATCH "sdhc_pin_1_match" = "&sdhc_sd_all_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 4*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdhc_sd_all_pins:sdhc_sd_all_pins{
            amlogic,setmask=<2 0x000000f0>;         /*sdhc b*/
            amlogic,clrmask=<5 0x00007c00           /*sdhc a*/
                                4 0x7c000000        /*sdhc c*/
                                2 0x0000fc00        /*sdio b*/
                                8 0x00000600>;      /*UART*/
            amlogic,pins="CARD_0","CARD_1","CARD_2","CARD_3","CARD_4","CARD_5";
            amlogic,enable-output=<1>; /* 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
//$$ MATCH "sdhc_pin_2_match" = "&sdhc_emmc_clk_cmd_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdhc_emmc_clk_cmd_pins:sdhc_emmc_clk_cmd_pins{
            amlogic,setmask=<7 0xc0000>;         /*bit[18-19] */
            amlogic,clrmask=<2 0x04c000f0           /*sdhc b & nand*/
                                5 0x00007c00        /*sdhc a*/
                                6 0xff000000>;        /*sdio c*/
            amlogic,pins = "BOOT_8","BOOT_10"; /** BOOT_10:CMD, BOOT_8:CLK */
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
//$$ MATCH "sdhc_pin_3_match" = "&sdhc_emmc_all_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 10 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdhc_emmc_all_pins:sdhc_emmc_all_pins{
            amlogic,setmask=<4 0x70000000
                             7 0xc0000>;         /*sdhc c*/
            amlogic,clrmask=<2 0x04c000f0           /*sdhc b & nand*/
                                5 0x00007c00        /*sdhc a*/
                                6 0xff000000>;        /*sdio c*/
            amlogic,pins = "BOOT_0","BOOT_1","BOOT_2","BOOT_3","BOOT_4","BOOT_5","BOOT_6","BOOT_7","BOOT_8","BOOT_10";
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
//$$ MATCH "sdhc_pin_4_match" = "&sdhc_sdio_clk_cmd_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdhc_sdio_clk_cmd_pins:sdhc_sdio_clk_cmd_pins{
            amlogic,setmask=<5 0x00000c00>;         /*sdhc a bit[10-11] */
            amlogic,clrmask=<2 0x058000f0           /*sdhc b*/
                                4 0x7c000000        /*sdhc c */
                                8 0x0000003f>;        /*sdio a*/
            amlogic,pins = "GPIOX_8","GPIOX_9"; /** BOOT_16:CMD, BOOT_17:CLK */
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };
//$$ MATCH "sdhc_pin_5_match" = "&sdhc_sdio_all_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 3*2 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"
//$$ L2 PROP_U32 = "amlogic,enable-output"
//$$ L2 PROP_U32 = "amlogic,pullup"
//$$ L2 PROP_U32 = "amlogic,pullupen"
        sdhc_sdio_all_pins:sdhc_sdio_all_pins{
            amlogic,setmask=<5 0x00006c00>;         /*sdhc a*/
            amlogic,clrmask=<2 0x058000f0           /*sdhc b*/
                                4 0x7c000000        /*sdhc c */
                                8 0x0000003f>;        /*sdio a*/
            amlogic,pins = "GPIOX_0","GPIOX_1","GPIOX_2","GPIOX_3","GPIOX_8","GPIOX_9";
            amlogic,enable-output=<1>; /** 0:output, 1:input */
            amlogic,pullup=<1>;
            amlogic,pullupen=<1>;
        };

//$$ MATCH "Camera_pin_0_match" = "&aml_cam_gpio_pins"
//$$ L2 PROP_U32 4 = "amlogic,setmask"
//$$ L2 PROP_STR 10 = "amlogic,pins"	
        aml_cam_gpio_pins: aml_cam_gpio_pins{
			amlogic,setmask=<3 0x80000
					         9 0x37c>;
			amlogic,pins = "GPIOH_9","GPIOY_6","GPIOY_7","GPIOY_8","GPIOY_9","GPIOY_10","GPIOY_11","GPIOY_12","GPIOY_13","GPIOY_14";
		};
		
//$$ MATCH "Camera_pin_1_match" = "&aml_cam_csi_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_STR = "amlogic,pins"	
		aml_cam_csi_pins: aml_cam_csi_pins{
			amlogic,setmask=<3 0x80000>;
			amlogic,pins = "GPIOH_9";
		};

//$$ MATCH "I2C_AO_pin_match" = "&ao_i2c_master"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 2 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
		ao_i2c_master:ao_i2c{
			amlogic,setmask=<10 0x60>;
			amlogic,clrmask=<10 0x1800006>;
			amlogic,pins="GPIOAO_4","GPIOAO_5";
		};

//$$ MATCH "I2C_A_pin_match" = "&a_i2c_master"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 6 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
		a_i2c_master:a_i2c{
			amlogic,setmask=<9 0xC0000000>;
			amlogic,clrmask=<0 0x3C0300 
			                 6 0xC00000
			                 8 0x1800000>;
			amlogic,pins="GPIODV_24","GPIODV_25";
		};

//$$ MATCH "I2C_B_pin_match" = "&b_i2c_master"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 6 = "amlogic,clrmask"
//$$ L2 PROP_STR 2 = "amlogic,pins"
		b_i2c_master:b_i2c{
			amlogic,setmask=<9 0x30000000>;
			amlogic,clrmask=<0 0x480 
			                 6 0x300000
			                 8 0x10780000>;
			amlogic,pins="GPIODV_26","GPIODV_27";
		};
		
// MATCH "I2C_D_pin_match" = "&d_i2c_master"
// L2 PROP_U32 2 = "amlogic,setmask"
// L2 PROP_STR 2 = "amlogic,pins"
		d_i2c_master:d_i2c{
			amlogic,setmask=<4 0xc>;
			amlogic,clrmask=<6 0x3000>;
			amlogic,pins="GPIOH_7","GPIOH_8";
		};

//$$ MATCH "remote_pin_0_match" = "&remote_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_STR = "amlogic,pins"
        remote_pins:remote_pin{
			amlogic,setmask=<10 0x1>;
			amlogic,pins="GPIOAO_7";
		};

//$$ MATCH "Audio_pin_0_match" = "&audio_pins"
//$$ L2 PROP_U32 4 = "amlogic,setmask"
//$$ L2 PROP_U32 10 = "amlogic,clrmask"
//$$ L2 PROP_STR 6 = "amlogic,pins"
        audio_pins:audio_pin{
            amlogic,setmask=<10 0x78000008>;
            amlogic,clrmask=<10 0x80002000>;
            amlogic,pins = "GPIOAO_8","GPIOAO_9","GPIOAO_10","GPIOAO_11","GPIOAO_13";
        };

//$$ MATCH "Spi_pin_0_match" = "&aml_spi_nor_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 2 = "amlogic,clrmask"
//$$ L2 PROP_STR 4 = "amlogic,pins"
		aml_spi_nor_pins: aml_spi_nor_pins{
			amlogic,setmask=<5 0xf>;
			amlogic,clrmask=<2 0x10380000>;
			amlogic,pins = "BOOT_11","BOOT_12","BOOT_13","BOOT_18";
		};
//$$ MATCH "meson_vcck_dvfs_pin_0_match" = "&aml_pwm_pins"
//$$ L2 PROP_U32 2 = "amlogic,setmask"
//$$ L2 PROP_U32 2 = "amlogic,clrmask"
//$$ L2 PROP_STR = "amlogic,pins"
		aml_pwm_pins:aml_pwm{
		    	amlogic,setmask=<3 0x1000000>;
			amlogic,clrmask=<0 0x48
					 7 0x10000020>;
			amlogic,pins="GPIODV_9";
		};

//$$ MATCH "dvb_p_ts0_pins_match" = "&dvb_p_ts0_pins"
//$$ L2 PROP_U32 1 = "amlogic,setmask"
//$$ L2 PROP_U32 2 = "amlogic,clrmask"
//$$ L2 PROP_STR 11 = "amlogic,pins"
		dvb_p_ts0_pins: dvb_p_ts0_pins {
			amlogic,setmask = <3 0x37>;
			amlogic,clrmask = <5 0xC0
								9 0x37C>;
			amlogic,pins = "GPIOY_9","GPIOY_10","GPIOY_11","GPIOY_12","GPIOY_13","GPIOY_14","GPIOY_6","GPIOY_7","GPIOY_0","GPIOY_1","GPIOY_8";
		};

//$$ MATCH "dvb_s_ts0_pins_match" = "&dvb_s_ts0_pins"
//$$ L2 PROP_U32 1 = "amlogic,setmask"
//$$ L2 PROP_U32 1 = "amlogic,clrmask"
//$$ L2 PROP_STR 4 = "amlogic,pins"
		dvb_s_ts0_pins: dvb_s_ts0_pins {
			amlogic,setmask = <3 0x17>;
			amlogic,clrmask = <9 0x378>;
			amlogic,pins = "GPIOY_9","GPIOY_0","GPIOY_1","GPIOY_8";
		};

	};
/// ***************************************************************************************
///	-	Ethernet
//$$ MODULE="Ethernet"
//$$ DEVICE="meson-eth"
//$$ L2 PROP_STR = "status"
    meson-eth{
		compatible = "amlogic,meson-eth";
		dev_name = "meson-eth";
		status = "okay";
		ethbaseaddr = <0xfe0c0000>;
		interruptnum = <40>;
		new_maclogic = <1>;
	};

/// ***************************************************************************************
///	-	RNG
//$$ MODULE="RNG"
//$$ DEVICE="meson-rng"
//$$ L2 PROP_STR = "status"
	meson-rng{
		compatible = "amlogic,meson-rng";
		status = "ok";
	};
///	-	DVB
//$$ MODULE="DVB"

//$$ DEVICE="dvb"
//$$ L2 PROP_STR = "ts0"
//$$ L2 PROP_U32 = "ts0_invert"
//$$ L2 PROP_U32 = "ts0_control"
//$$ L2 PROP_STR 6 = "pinctrl-names"
//$$ L2 PROP_CHOICE "dvb_p_ts0_pins_match" = "pinctrl-0"
//$$ L2 PROP_CHOICE "dvb_s_ts0_pins_match" = "pinctrl-1"
	dvb{
		compatible = "amlogic,dvb";
		/*"parallel","serial","disable"*/
		ts0 = "parallel";
		ts0_control = <0>;
		ts0_invert = <0>;
		pinctrl-names = "p_ts0", "s_ts0";
		pinctrl-0 = <&dvb_p_ts0_pins>;
		pinctrl-1 = <&dvb_s_ts0_pins>;
	};

//$$ DEVICE="dvbfe"
//$$ L2 PROP_STR = "dtv_demod0"
//$$ L2 PROP_U32 = "dtv_demod0_i2c_adap_id"
//$$ L2 PROP_U32 = "dtv_demod0_i2c_addr"
//$$ L2 PROP_U32 = "dtv_demod0_reset_value"
//$$ L2 PROP_STR = "dtv_demod0_reset_gpio"
//$$ L2 PROP_U32 = "fe0_dtv_demod"
//$$ L2 PROP_U32 = "fe0_ts"
//$$ L2 PROP_U32 = "fe0_dev"
//$$ L2 PROP_STR 6 = "pinctrl-names"
//$$ L2 PROP_CHOICE "dvb_fe_pins_match" = "pinctrl-0"
	dvbfe{
		compatible = "amlogic,dvbfe";
		dtv_demod0 = "Si2168";
		dtv_demod0_i2c_adap_id = <4>;
		dtv_demod0_i2c_addr = <0x64>;
		dtv_demod0_reset_value = <0>;
		dtv_demod0_reset_gpio = "GPIOY_3";
		fe0_dtv_demod = <0>;
		fe0_ts = <0>;
		fe0_dev = <0>;
	};

/*	dvbfe{
		compatible = "amlogic,dvbfe";
		dtv_demod0 = "Mxl101";
		dtv_demod0_i2c_adap_id = <4>;
		dtv_demod0_i2c_addr = <0x60>;
		dtv_demod0_reset_value = <0>;
		dtv_demod0_reset_gpio = "GPIOY_3";
		fe0_dtv_demod = <0>;
		fe0_ts = <0>;
		fe0_dev = <0>;
	};
*/
        mesondrm {
                compatible = "amlogic,meson8b";
                dev_name = "mesondrm";
        };
}; /* end of / */